Perforated flexible single wall HDPE drain, with corrugated interior and exterior walls for drainage application use

The Type 2 drain perforations has a 1.8 mm sluice.

• Offered with a filtering sheath or not, according to the results of the granulometric analysis or the backfill material used.
• Fits perfectly with our complete range of injected accessories, guaranteeing a high-performing and resistant assembly.
• Product accredited WELL MADE HERE

Available with the following filtering sheaths:

• Nonwoven polyester with 100-micron openings
  
• Nonwoven polypropylene with 250-micron openings
  
• Woven polyester with 450-micron openings

Meets the criteria of BNQ 3624-110 standards

Recommandation : Several factors enter into the selection of the product to be used. Therefore Soleno recommends a granulometric analysis before undertaking a drainage project in order to choose the right pipe according to the type of soil.

Flexible corrugated drain with smooth interior wall 25% more efficient that traditional corrugated drain*

Now certified to BNQ 3624-115.

• Provides a better Manning’s value (0.012) than the standard corrugated drain, to promote rapid water evacuation.
• Thanks to its flexibility, this corrugated drain with smooth interior wall requires fewer connections than rigid pipes.
• Its smooth interior wall minimizes sediment accumulation, while greatly facilitating cleaning.
• Offered with a filter sheath of nonwoven polypropylene with 250-micron openings or not, according to the results of the granulometric analysis or the backfill material used.
• Offered with Type 1 perforations (non perforated), Type 2 (1.8 mm sluice) and Type 3 perforations (3 mm sluice).
• The Type 3 perforations slow down the obstruction of the sluices caused by the presence of iron ochre.
• Conforms to the National Building Code of Canada.

Product now accredited WELL MADE HERE!

*Calculated with a slope of 0.10%

The MarMac PolySeal coupler is a heavy-duty flexible joint that permanently seals and secures corrugated plastic pipes.

• PolySeal fittings are custom-made, reinforced external joints designed to connect corrugated HDPE/PPHD pipes, while offering resistance to infiltration and exfiltration.
• Consists of multiple layers; a woven polypropylene reinforcement, compression straps, a rubberized mastic sealer and a cross-laminated HDPE layer.
• Allows the connection of pipes with plain ends and diameters from 200 mm (8 in) to 1500 mm (60 in).

Perforated flexible single wall drain, with corrugated interior and exterior walls for drainage application use

The Type 3 drain perforations has a 3 mm sluice.

• Offered with a filtering sheath or not, according to the results of the granulometric analysis or the backfill material used.
• Fits perfectly with our complete range of injected accessories, guaranteeing a high-performing and resistant assembly.
• Product accredited WELL MADE HERE

Available with the following filtering sheaths:

• Nonwoven polyester with 100-micron openings
• Nonwoven polypropylene with 250-micron openings
• Woven polyester with 450-micron openings

Meets the criteria of ASTM F667 and meets the requirements of OPSS 1840

Recommandation : Several factors enter into the selection of the product to be used. Therefore Soleno recommends a granulometric analysis before undertaking a drainage project in order to choose the right pipe according to the type of soil.

 

Nonwoven needled geotextile, compliant with MTQ standards, mainly used for civil engineering works

Made of polypropylene, Routex IV is mainly used for filtration and separation.

• Due to their three-dimensional construction and their filtration openings size, nonwoven geotextiles provide an improved permeability over woven geotextile.
• The Routex IV nonwoven geotextile is designed specifically to meet the requirements for products specified by the Quebec Ministry of Transport (MTQ).
• Physical and mechanical characteristics corresponding to MTQ type IV geotextiles.
• Installed around the net stone backfill in a drainage trench application.
• Certified by the BNQ according to standard BNQ 7009-210 and the grade F1.
• Compliant with the CCDG of MTQ.

Selection of the geotextile will be made according to the mechanical and hydraulic properties required.

Now offered in rolls of 3.81 m (12.5 ft).

Single-walled, flexible perforated pipe, corrugated inside and out for below grade applications

The Solflo perforations (Type 2) provide an aperture of 1.8 mm.

• Provides a compression stiffness of 210 kPa or 300 kPa, depending on the diameter selected.
• Has a high load-bearing capacity.
• Supports a higher load with respect to the drain in drainage trench applications.
• Offered with a filtering sheath or not, depending on the type of soil to be drained or the backfill material used.
• Perforated Solflo should always be coated when installed in draining sand in a drainage trench application.
• Fits perfectly with our complete range of fittings and accessories with the exclusive technology of double bells with clips (DBC), ensuring the quality of the installation.
• Product now accredited WELL MADE HERE

Meets the criteria of BNQ 3624-110 and AASHTO M294 standards

Perforated rigid dual wall pipe, with smooth interior and corrugated exterior walls for roadway use

• Provides a compression stiffness of 210 kPa or 320 kPa, depending on the selected diameter, up to 900 mm (36 in). Please refer to the data sheet for diameters from 1050 mm (42 in) to 1500 mm (60 in),
• Durable and resistant solution to de-icing salts.
• The length of the pipes reduces installation time and the number of joints required, compared to traditional concrete pipes.
• Offered with a filtering sheath or not, depending on the type of soil to be drained or the backfill material used.
• Perforated Solflo Max should always be filtered when installed in draining sand in a trench drain application.
• The use of Perforated Solflo Max is ideal for collectors since the coefficient of roughness is lower than that the interior wall of corrugated pipes.
• Fits perfectly with our complete range of non-watertight fittings and accessories, featuring our exclusive locking bell technology, ensuring quality installation.
• Product accredited WELL MADE HERE

Meets the criteria ofBNQ 3624-120, CSA B182.8, ASTM 2648, ASTM 2306, AASHTO M294 standards